Analysis of the results of the use UAV Trimble UX-5 for creation of orthophotomaps and digital model of relief
Journal Title: Геодезія, картографія і аерофотознімання - Year 2015, Vol 81, Issue 1
Abstract
Purpose. The purpose of this paper is to analysis and research capabilities of unmanned aerial vehicle (UAV) Trimble UX5 to create orthophotomap and digital elevation models (DEM), as well as identifying and addressing possible shortcomings in the aerial survey and processing of aerial photographs. Methods. Before starting aerosurveying conducted reconnaissance of the area. For nose-up and glide-path elected corresponding surface area on the ground had areal options on listed specifications for the UAV, and satisfy the conditions for launching and landing UAV.For preliminary design and calculation works software was used Trimble Access Aerial Imaging, which install a protected field controller Trimble Tablet, which is used to control UX5.UAV aerial survey was carried out with a digital camera SONY NEX 5R.Since the UAV UX5 stipulated the establishment of two-frequency GPS-receiver for in-flight values of projection centers, it was done discharged horizontal and vertical tie-in markings.For operative creation of orthophotomap used photogrammetric module Trimble Business Center Photogrammetry Module, the company Trimble, with which you can create a point cloud, triangular irregular grids (TIN- model) and plan to display contour lines, terrain over was carried out aerial aerosurveying.To confirm the possibility of using digital stereophotogrammetric method calculated apriori estimate of the accuracy of the spatial coordinates of the area. To assess the accuracy of the terrain defined checkpoints at three pilot sites. Coordinates of points determined during VFR GPS – receivers Trimble R7 mode RTK. After creating orthophotomap they measured the coordinates of the above points and calculated root-mean-square error measured relative to the coordinates on the ground. Results. For aerial survey conducted with a height of 150 m, 200 m and 300 m on the received images were calculated mean square error provisions terrain contour points, which confirm the possibility of using aircraft model Trimble UX5 to produce topographic maps at scales of 1: 500, 1: 1000 and 1: 2000 section 0.5-1 m contour for these scales and 1 m for the third scale. The scientific novelty. Based on a critical analysis of the design and operational features Trimble UX5 UAV developed technological scheme to evaluate the fitness of UAV aerosurveying both quantitative and qualitative parameters. This will enable further evaluate any models UAV regarding their use in digital stereofotohrammetryc method of creating large-scale orthophotomap and topographical plans. The practical significance The use of UAVs Trimble UX5 allows you to take difficult territory, with the required precision to produce large-scale topographic and cadastral plans in the application of digital stereophotogrammetric method that can significantly reduce the cost of the process of creating the above plans.
Authors and Affiliations
A. I. Vovk, V. M. Hlotov, А. V. Hunina, A. Y. Malitskyi, K. R. Tretyak, A. Tserklevych
Keywords
Related Articles
- EP ID EP484669
- DOI 10.23939/istcgcap2015.01.090
- Views 161
- Downloads 0
Efficiency of application of satellite technology when performing land and cadastral works in settlements
Purpose. The purpose of this work is to study the effectiveness of using satellite technology in real-time kinematics mode for work performed to determine the areas of land of different size within a settlement. Methodol...
Evaluation of three-dimensional deformation fields of the earth by methods of the projective differential geometry. Rigid rotations of the Earth
Aim. The aim is this research is the evaluation of the Earth’s rigid rotation as a component of global deformation fields in interconnection with angular distortions of the geocentric spatial coordinate system. Methodolo...
Update of topographic maps of Iraq, scale of 1: 50 000 using satellite image – ikonos
The aim is to find accurate, fast and economical way to update maps with information obtained by remote sensing data. There were all the necessary research to update the maps of the study area city of Kerbala (Iraq) scal...
Analysis of stability of points of automated geodetic monitoring of engineering structures Kanev HPP
Aim. As part of the project of renovation of hydropower plants on the Kanev hydropower plants (HPP) the experts of Leica Geosystems together with Ukrhydroenergo had created a system of automated geodetic monitoring compr...
Determination of the geoid – gravity field and topography of the Black sea according to the satellite altimetry data
Objectives. The method of satellite altimetry as a relatively new approach to precise satellite surveying, which provides the different Earth sciences by a most complete information about the state of the ocean and its c...