CHOICE OF THE OPTIMAL PARAMETERS OF MEASURING THE SHAFT ROTATION FREQUENCY OF THE HYDRAULIC TRANSMISSION OF THE LOCOMOTIVE USING MICROCONTROLLER
Journal Title: Наука та прогрес транспорту - Year 2017, Vol 0, Issue 2
Abstract
Purpose. The article provides for finding solution to the problem of developing and improving the means for measuring tachometric data of the previously created information and measuring system for testing hydraulic locomotive transmission by substantiating the optimal sensor design and signal processing algorithms. At the same time first of all it is necessary to start from the possibility of modifying the already existing test bench for hydraulic locomotive transmissions at the Dnipropetrovsk diesel locomotive repair plant «Promteplovoz». Methodology. In the work, the researchers proposed a methodology for modifying the sensor design and the algorithm for processing its signals. It is grounded on previous developments of tachometric sensor of the optical type on the basis of D-2MMU-2 sensor of the microprocessor automated test bench system of hydraulic locomotive transmission in the locomotive repair plant conditions. Selection of the necessary measurement algorithm and the number of sensor teeth is substantiated by calculating instrumental and methodological errors. Also, the studies aimed at identifying the source of interference in the measurement of rotational speed are described and solution for its elimination has been found. Findings. For the designed rotation speed sensor of the optical type based on the existing D-2MMU-2 sensor, the authors analyzed the dependence of the methodological and instrumental errors. Based on the obtained data more rational variant of the rotation speed calculation algorithm is proposed, and the number of teeth of the sensor disk is justified. Further, the main source of measurement interference was established and a method for improving the hardware of the hydraulic locomotive test bench was proposed. Originality. There were conducted the studies according to the methodological and instrumental errors of the designed rotation speed of sensor. The mechanisms of interference filtering arising from the sensor rotation speed fixing were proposed. Additional studies have shown the need for a hardware revision of signal conditioner scheme. Practical value. Conducted studies make it possible to establish a rational number of sensor disk teeth, which allows improving the measurement algorithm. It was also performed a hardware improvement of signal conditioner scheme from the sensor, helping to get rid of interferences. The results of measurements in studies are the initial data to perform further studies in order to determine the technical condition of hydraulic transmission UGP 750-1200 during factory testing after repair.
Authors and Affiliations
I. V. Zhukovytskyy, I. A. Kliushnyk
Keywords
Related Articles
- EP ID EP228322
- DOI 10.15802/stp2017/99945
- Views 79
- Downloads 0
WATER CLEANING FROM RESIDUES OF MEDICINAL PREPARATIONS
Purpose. The paper aimed at analyzing the presence of residual quantities of medicinal preparations in the water of Ukraine and the world. Based on the world and own experience to propose methods for waters cleaning from...
ПРОБЛЕМЫ ОРГАНИЗАЦИИ ПАССАЖИРСКИХ ПЕРЕВОЗОК НА ЖЕЛЕЗНЫХ ДОРОГАХ США
Цель. В работе необходимо провести исследование организации работы железнодорожного транспорта США при выполнении пассажирских перевозок. Методика. Исследования выполнены на основании анализа литературных источников и от...
ПЕРСПЕКТИВИ УКЛАДАННЯ СКРІПЛЕННЯ ТИПУ СКД 65-Б В КРИВИХ ДІЛЯНКАХ КОЛІЇ МАЛОГО РАДІУСА
Мета. На сьогоднішній день існує тенденція щодо повного переходу головних колій на залізобетонні шпали. Причиною цього є дефіцит дерев'яних шпал, їх висока вартість та низький термін служби, що в кривих ділянках колії ра...
ВЛИЯНИЕ ЛОПАСТНЫХ И ПРОФИЛЬНЫХ ХАРАКТЕРИСТИК НА ГИДРОДИНАМИЧЕСКУЮ ЭФФЕКТИВНОСТЬ ГРЕБНЫХ ВИНТОВ
Цель. Для обоснования экспериментальных методов необходимо: 1) сформировать 3D-модели исследуемых гребных винтов; 2) изучить влияние профилировки лопасти гребного винта на его гидродинамические характеристики; 3) разрабо...
РАСПРЕДЕЛЕНИЕ ПОДВИЖНОГО СОСТАВА ДЛЯ ОТСТОЯ МЕЖДУ ПУТЯМИ ОБЩЕГО И НЕОБЩЕГО ПОЛЬЗОВАНИЯ
Цель. Особую актуальность в условиях увеличения доли приватных вагонов приобретают задачи выбора оптимальных режимов взаимной работы путей общего и необщего пользования. Поэтому целью настоящей работы является разработка...