Design of fire-resistant heat- and soundproofing wood wool panels
Journal Title: Восточно-Европейский журнал передовых технологий - Year 2019, Vol 3, Issue 10
Abstract
<p>The conducted research revealed the possibility to manufacture heat- and soundproofing materials for the arrangement of buildings. Wood fibers, which are produced in the form of flat panels, are the raw materials for their production. The mechanisms for the process of heat- and soundproofing during energy transfer through the material, which enables influencing this process, were established. It was proved that they are related to the porosity of the material. Thus, at a decrease in volume weight of the material, thermal conductivity and sound transmission are reduced, and vice versa. In addition, heat- and soundproofing building materials from wood should meet the following requirements: to have stable thermal insulation and acoustic indicators within the whole operation period and to be fire resistant, not to give off hazardous substances into the environment. Experimental research proved that the material based on wood wool and inorganic binder at the ratio of 1:1 belongs to combustible materials, because there was its smoldering during the temperature exposure. Thus, under thermal exposure for 90 seconds, the sample caught fire, the flame propagated around the first three zones within 41 s. At the same time, an increase in the amount of the binder on inorganic base and application of organic-mineral binder does not lead to the ignition of material, the maximum temperature of flue gases made up around 120 °C and flammability index amounted to 0. This became possible due to the decomposition of fire retardants under the influence of temperature with emitting non-combustible gases, inhibiting the processes of material oxidation and significantly increasing the formation of the heat protective layer of coke on the surface of the material. This leads to inhibition of heat transfer of high-temperature flame to the material. This made it possible to determine the conditions for fire-resistance of the material through the formation of a thermal conductivity barrier. This makes it possible to argue about the relevance of the detected mechanism of formation of properties of the material based on wood wool and inorganic or organic-mineral binder, as well as practical attractiveness of the proposed technological solutions. The latter, in particular, relate to determining the amount of the binder component (the ratio of wood wool to the binder is not less than 1:2), because in small quantities (ratio 1:1), the burning process occurs. Thus, there are the grounds to argue about the possibility of directional regulation of the processes of formation of heat- and soundproofing wood materials through the use of wood wool and the binder. In this case, it was proposed to use the inorganic and organic-mineral coatings as a binder, which can form a fireproofing film at the surface of the material.</p>
Authors and Affiliations
Yuriy Tsapko, Denys Zavialov, Olga Bondarenko, Olena Pinchevsʹka, Nataliia Marchenco, Sergii Guzii
Keywords
Related Articles
- EP ID EP666484
- DOI 10.15587/1729-4061.2019.166375
- Views 56
- Downloads 0
Development of the formulation for extruded products based on sugar corn grain and determining their quality indicators
<p class="par-indent">The formulations of extruded products based on sweet corn grain, bare-grain barley, carrot root crops, and licorice root and collagen hydrolysate have been developed.</p><p class="par-indent">We det...
Development of a model for the integrated management of the international delivery chains formation
<p>We propose a model for the formation of international logistics chains based on an integrated multicriterial analysis of potential cargo transportation routes and delivery cost. The application of the systemic approac...
Improving efficiency of machining the geometrically complex shaped surfaces by milling with a fixed shift of the cutting edge
<p>In order to improve efficiency of machining by milling geometrically complex shaped surfaces, mainly the methods related to improvement of properties of the tool material, change of composition and properties of the t...
Development of a technique for restoring the efficiency of film ITO/CdS/CdTe/Cu/Au SCs after degradation
<span lang="EN-US">A study into the influence of direct polarity on the output parameters of ITO/CdS/CdTe/Cu/Au solar cells (SC) has been conducted. We have experimentally registered the effect of an electric field of di...
Development of measures to improve milk quality and safety during production
<p>The number of somatic cells in cow milk affects its quality indicators, grade and safety. The level of somatic cells in milk depends on the state of the udder in animals. That is why it is important to diagnose sub-cl...