EVALUATION OFMICROTENSILE BOND STRENGTH AND NANOLEAKAGE AFTER DOUBLE LAYER ADHESIVE COATING APPLICATION USING BULK FILL COMPOSITE.
Journal Title: International Journal of Advanced Research (IJAR) - Year 2018, Vol 6, Issue 10
Abstract
Aim:The present study used toevaluatenanoleakage and microtensile bond strength after double layer adhesive coating application. The tensile bond strength of an adhesive system is mostly influenced by the hybrid layer, followed by resin tags in the dentinal tubule and finally by chemical bonding. However, porosities can be observed at the bottom of hybrid layers. This phenomenon was termed ?nanoleakage? Sano et al,They had seen incomplete penetration of hybrid layers during adhesive bonding techniques.Thenanoleakage effect has been discussed to be one factor negatively affecting the quality of dentinal bonding. Influence of nanoleakage on microtensile bond strength was determined using different visualization techniques. For instance, resin?dentin specimens were prepared and immersed in silver nitrate that penetrated into nanoleakage. Subsequently, specimens were broken at the adhesive interface (commonly using tensile testing), and nanoleakage was visualized indirectly on the exposed surface using scanning electron microscopy (SEM). It has been postulated that, between polymerization shrinkage and microtensile bond strengths (μTBS) a highly significant correlation was found because forces developed during the polymerization of dental restorative composites placed in a restricted setting, cause tension in the material, with possible subsequent distortion of the bond to the tooth. Material and methods: 40 human molars stored in deionized water will used. Teeth will be divided into four equal groups according to application mode (self-etch vs. Etch-and-rinse mode). group A: using filtekTM bulk fill with single bond universal adhesive (self-etching mode), then application of hydrophopic resin coating (Heliobond). group B: using filtekTM bulk fill with single bond universal adhesive (self-etching mode), without application of hydrophobic resin coating. group C: using filtekTM bulk fill with single bond universal adhesive (etch and rinse mode), then application of hydrophobic resin coating. group D: using filtekTM bulk-fill with single bond universal adhesive (etch-and-rinse mode), without application of hydrophobic resin coating. Results: It was found that the filtekTM bulk fill composite with self-etch mode application of adhesive followed by coating application revealed the highest mean ?-TBS value (41.9 MPa) followed by filtekTM bulk fill composite with self-etch mode application of adhesive without coating application (39.7MPa). FiltekTM bulk fill with self-etch mode followed by coating, showed the highest Nanoleakage results (55.4%), while FiltekTM bulk fill with etch-and-rinse mode followed by coating, showed the lowest Nanoleakage results (39.9%).Conclusion: multiple consecutive coating during dentin bonding improved the bond strength for etch-and-rinse adhesive and reduced nanoleakage due to increases in the amount of resin impregnation within the hybrid layer. Nevertheless the better performance of the bulk-fill composites, all clinician should not consider that the bulk-fill composites are perfect substitutes for conventional composites.
Authors and Affiliations
Labib Mohamed Labib, Sameh Mahmoud Nabih, Hamed elkady.
Keywords
Related Articles
- EP ID EP410226
- DOI 10.21474/IJAR01/7920
- Views 35
- Downloads 0
IMPACT OF ELECTRICITY SUPPLY ON SUSTAINABILITY OF AGRICULTURE ACTIVITYIN HARYANA.
The development of the agriculture sector as change for inclusive growth of any economy in the world is very important. At present, numerous of developing and under developing countries, the agriculture sector is generat...
AUTOIMMUNE ENCEPHALITIS: A POTENTIALLY TREATABLE CAUSE OF ACUTE PSYCHOSIS.
Autoimmune encephalitis is a difficult clinical diagnosis due to predominance of psychiatric symptoms and the similarities in the clinical, imaging and laboratory findings of many forms of encephalitis especially infecti...
MINIMALY INVASIVE SURGICAL TECHNIQUE USING CHORION MEMBRANE IN THE TREATMENT OF INTRABONY DEFECTS CASE REPORT.
The main purpose of periodontal treatment is to eliminate inflammatory processes in order to arrest the progression of the disease and keep the dentition in a state of the health. Thus the ultimate goal of periodontal th...
THE AMBIENT SCRUTINIZE OF SCHEDULING ALGORITHMS IN BIG DATA TERRITORY.
Today scenario, we live in the data age and a key metric of existing times is the amount of data that is originates ubiquitously around us. At present-time intense increase in the number of Internet subscriber and connec...
LAPAROSCOPIC MANAGEMENT OF PEDIATRIC GALL STONE DISEASE.
Objective: to describe our experience in evaluating the role of laparoscopic cholecystectomy (LC) in management of gallstone disease in children. Methods: A prospective study carried out on 20 patients with calculerchole...