Features of structure and properties of modified multicomponent alloys
Journal Title: Інформаційні системи, механіка та керування - Year 2016, Vol 0, Issue 14
Abstract
Study of state of the problem of formation of structure and properties of compact enhance steels and alloys used for cast and deformed pieces of mechanical engineering and aerospace engineering. To solve this problem is provided a method of modifying metal melts dispersed nanosized refractory formulations range. The material of the study were multi-component (heat-resistant) nickel alloys for blades aviation gas turbine engines (GTE) and Si- Mn steels used for gas and oil pipes and welded structures responsible. The chemical composition of heat resisting nickel alloys,% wt .: Al-4,0%; Ti-2,5; Cr-11.0; Mo-3,8; W-3,8; Co-8,0; C-0,09; Fe-2,0; Ni- base. The chemical composition of 15GS and 16GS,% wt .: C-0.16 Si- Mn steels; Si-0,70; Mn-1,20; Cr <0,3; Ni <0,3; Cu <0, 3; S <0,040; P <0,035. Reasonable selection guidelines Nanodisperse complex modifiers in relation to the composition of alloys. Compositions designed nanomodifiers heat resisting nickel alloys, titanium based carbonitride powders of Ti (C, N); kremniymargantsovistyh for steel - based on titanium and aluminum. The formulations are patented modifiers. The laboratory and pilot-scale melting of the alloys with varying number of members of modifiers. An experimental set optimal amount of injected modifier 0,10..0,20% of the mass of the melt. The initial size of 60..100 nm nanopowders obtained by plasma-chemical synthesis. The study granulometry powder specific surface modifier particles picked Ti (C, N) and Ti; crystallographic parameters. Modifiers administered in tablet form in the melt. Installed temperature and time parameters modification. Duration complex modifiers make up for nickel alloys up to 5 minutes for the steel -15 min. In industrial conditions experienced cast castings for turbine engine blades and blanks for further deformation. The samples - witnesses investigated the structure, mechanical and corrosion properties of alloys in the original and modified state. As a result, a substantial modification achieved grain refinement Ni-alloys from 5..8mm to 0,5..1mm. and stalyah- Si- Mn 1.5. The phase composition of the alloy by X-ray electron microprobe analysis. The formation of dispersed carbide phases in the Ni-alloys, both inside and along the grain boundaries, as well as strengthening of intermetallic compounds dispersed Ni3Ti. Achieved increase of properties for Ni-alloys: σв 7%, δ-24%, KCU-46%; for Si- Mn steels: σв - 23%, δ-18%, KCU-40%
Authors and Affiliations
Александр Васильевич Калинин,, Анастасия Вячеславовна Кашенкова,, Наталья Евграфовна Калинина
Keywords
Related Articles
- EP ID EP540709
- DOI -
- Views 84
- Downloads 0
The stress-strain state determination in pipelines welded joints
Stress-strain state in welded joints of pipelines was determined. An axisymmetric calculation model was used,n the study of stress concentration in a weld. The dependences of stress and strain distribution in the weld zo...
EXPERIENCE OF COMPOSITE MATERIALS APPLICATION IN THE CONSTRUCTION OF EXPERIMENTAL TUBE LAUNCH UAV
High flight performance of the unmanned aerial vehicle (UAV) is achieved by the minimum weight airframe, powerplant, and other useful equipment and its elements. One of the effective way of minimizing the structural weig...
Про проблеми і методи знаходження малорозмірних об'єктів на зображеннях
<p>В даній статті розглядається особливості проектування системи наведення безпілотного літального апарату, яка працює в режимі реального часу. Для детектування малорозмірного безпілотного літального апарату запропонован...
Way to safely routing GRID SYSTEMS
The article gives an introduction to distributed computing (distributed computing) - a way to solve time-consuming tasks (computing and data processing tasks), namely, technology development and use of large grid systems...
Оптимизация длительности реализации при структурном анализе измерительного сигнала
<p>Экспериментально показано, что при цифровой обработке бесконечной реализации случайной последовательности априорно известной сигнальной конструкции ограниченной длительности, ее классификационные признаки исчезают.</p...