Influence of the conditions of casting and heat treatment on the structure and mechanical properties of the AlMg10 alloy
Journal Title: Journal of Achievements in Materials and Manufacturing Engineering - Year 2017, Vol 1, Issue 83
Abstract
Purpose: Assessment of the possibilities of shaping the structure and improvement of mechanical properties of casting from AlMg10 alloy through a selection of casting technology and precipitation hardening. Design/methodology/approach: the work evaluated the impact of casting and heat treatment technology on the mechanical properties and structure of AlMg10 alloy castings. The tests were performed on 200 mm × 100 mm × 25 mm plate castings produced by gravity casting methods for sand and metal moulds and by a liquid state press moulding technology. Castings made with these technologies solidify in substantially different heat- evaporation conditions and exhibit varying degrees of primary structure fragmentation. Metallographic and strength tests were performed on raw castings and after heat treatment. Findings: The changes in the morphology and size of primary crystals and the dispersion of the reinforcing phase according to the casting solidification rate and the precipitation hardening treatment were analyzed. Solidifying castings in the form of sand show a globular structure, whereas in die and press castings, a typically dendritic structure occurs, with the dendritic crystals in pressed castings being much smaller in size than the die castings. In castings which were not heat-treated, the reinforcing phase of Al3Mg2 occurs in interdendritic spaces, and its dispersion increases with the rate of cooling. After supersaturation and ageing treatments, the phase α has a grain structure in all samples. The largest dispersion of reinforcing molecules is characterized by press castings. In a raw state, the highest mechanical properties are shown by castings made in the form of sand and the method of pressing in a liquid state. Heat treatment of AlMg10 alloy castings significantly influences the increase of mechanical indexes in all castings investigated. The highest features of Rm are approx. 330 MPa and A5 above 10% is obtained in castings made by the press method. Research limitations/implications: Particular attention should be paid to the avoidance of the effects of slag inclusion, shrinkage and magnesium oxidation during casting of AlMg10 alloys. In die castings of a plate type, due to own stresses, a significant decrease in mechanical properties occurs. Practical implications: The most advantageous mechanical properties of AlMg10 alloy castings are obtained by using liquid-state pressing technology. In addition, this technology makes it possible to produce thin-walled castings of high dimensional accuracy, high air- tightness, fine grain structure, lack of surface defects and low roughness. Originality/value: The paper presents the possibility of improving the mechanical properties of AlMg10 castings by applying heat treatment. It has been proven that the casting method has a significant effect on the mechanical properties of the castings.
Authors and Affiliations
P. Kordas
Keywords
Related Articles
- EP ID EP226112
- DOI 10.5604/01.3001.0010.5137
- Views 119
- Downloads 0
Effect of diffusion borochromizing on microstructure, microhardness and corrosion resistance of tool steel with different carbon content
Purpose: The aim of this paper is presents the study results concerning influence of carbon content on the surface layer condition, microstructure, microhardness and corrosion resistance of diffusion boroc...
Cellulose based micro- and nanocomposites
Purpose: In this study, the comparative role of micro-and nano- sized cellulose powder in exploring the influence on the mechanical properties of high density polyethylene (HDPE) composites was investigated. Desig...
Optical properties of PVP/ZnO composite thin films
Purpose: The aim of the work was the preparation of thin composite layers from PVP polymer doped by ZnO nanoparticles using the spin coating method and the analysis of the applied reinforcing phase on the morphology and...
Analysis of improvements in technological properties of WC-Co tool materials fabricated by spark plasma sintering
Purpose: The technological properties of WC-Co tool materials fabricated by spark plasma sintering has been investigated.Design/methodology/approach: The technological properties has been investigated using instrum...
The microstructure and mechanical properties of FSPed HSLA steel
Purpose: High-strength low-alloy (HSLA) steels have been used in a wide range of applicationsfrom automotive to ship building industry due to their low weight, formability and good weldability.However, especially in the...