Prediction of Temperature Distribution within a Piece of Date Palm Trunk during the Microwave Heating Treatment to Control Rhynchophorus Ferrugineus

Journal Title: Journal of Agricultural Machinery - Year 2018, Vol 8, Issue 2

Abstract

Introduction In recent decays, the microwave heating treatment is one of the best ways for the pest control. It is difficult to determine temperature in different parts of materials by Thermometer, but we can solve this problem by Comsol Multiphysics Software. In a research, results of a farm test were consistent with laboratory data and high temperature area was belonged to the outer part of wooden piece (Massa et al., 2015). The numerical simulation of Microwave heating was successfully done for fruits and compared with experimental measurement in two cylindrically and spherically states by Zhao et al. (2011). The results indicated that, the temperature prediction in a wooden piece under heating of a Microwave system was in conformity with experimental infra-red rays data (Rattanadecho, 2006). The outer part of the piece was impressed by inspired heating and the inner part by transmission of heating (Massa et al., 2011). A high frequency structure simulator software, a radiant trumpet shaped antenna with 2.45GHz frequencies, 100 watt electric power were the tools that were used to predict the temperature at a Date Palm Wooden piece at 10, 12, 14 and 16 centimeters (Al Shwear and Remili, 2016). Microwave pretreatment was studied with two factors of Microwave radiation (170, 450, and 850 W) and Microwave duration (2, 6, and 10 min). It can be concluded that the Ozonolysis is the most effective pretreatment regarding to saccharification percentage of sugarcane bagasse (Eqra et al., 2015). This study has been done with the aim of fighting with Rhynchophorus ferrugineus blight by microwave and removing toxins in crops. Materials and Methods Samples features such as physical, mechanical and magnetic once were established in both Tehrans Material and Energy lab and Polymer and Petrochemical Research Center, Then it was simulated by Time_ Temperature profile software. For simulating research by Comsol Multiphysics software, at first sample and chamber sizes were determined and the type of material, meshing, 2.45GHz frequencies and the time duration of heating were measured, respectively. Finally the research was analyzed and Time‌_Temperature profile which was one of the outcomes of Multiphysics software was determined. A cubic piece of wood (103×86×78 mm) (Fig. 1), a Digital Thermometer and a Microwave are the tools which the researcher used in this sample. The temperature was measured at three different parts of cub diagonal by Thermometer. At first, the wooden sample was divided in two equal parts and a sensor was placed in the middle of it and then it was placed in the Microwave. The primary temperature of sample and Microwaves was 27°C. We turn the Microwave on for a period of 10 minutes, after that we check the wooden piece temperature by Thermometer at 20 seconds intervals. Results and Discussion T-test was used to compare statistical results achieved by simulated and experimental temperature of cubic diagonal. According to T mark at 5 percent level, we can say that there is a significant difference between simulated and experimental temperature at point1, however, there is no such a significant difference at 2 and 3 points. In the following phase, the temperature was compared at two simulated and experimental states by variance analysis test. There was significant difference at 1, 2 and 3 points according to data are shown at figure 4. Moreover, Duncan Post hoc test is shown at figures 5 and 7 that experimental temperature shows no difference at 1 and 3 points but it makes difference at 1, 2 and 2, 3 points. Conclusion Results show that the simulation model can predict the temperature in different parts of a wooden sample. The temperature will be higher as much as the points will be closer to the wave producer resource. In order to control pests in the trunk of a tree, we should use several wave generator systems, instead of ones. It is recommended that cylindrical microwave should be simulated and designed instead cubic ones, because it is better adjusted with tree stock and the wave generator system is placed on this surface so that the temperature will be distributed symmetrically along the diagonal.

Authors and Affiliations

S. Mollazehi,H. Sadrnia,M. R. Bayati,

Keywords

Related Articles

The effect of acoustic system variables on sound signals of Melon varieties

Introduction Cucumis melo includes a wide range of varieties. The acoustic is production, transmission and energy received form medium vibrations. Acoustic or sonic tests applies for grading productions, ripening determi...

The Effect of Nozzle Types and Time of Herbicide Incorporation in Soil on Corn (Zea mays L.) Weed Control

This experiment was conducted to study the effect of nozzle types and the time of herbicide incorporation in soil on weed control, using split plot design by randomized block design. The main plots were soil and herbicid...

Effect of Infrared Drying on Drying Kinetics and Color Changes of Wild Sage Seed Mucilage

In this study, the effects of infrared (IR) dryer system parameters such as IR power, the distance of mucilage from lamp surface, mucilage thickness on drying kinetics and, color indexes (L*, a*, b* and ΔE) of wild sage...

Investigating the Mechanical Properties and Degradability of Bioplastics Made from Wheat Straw Cellulose and Date Palm Fiber

During the past two decades, the use of bioplastics as an alternative to regular plastics has received much attention in many different industries. The mechanical and degradable properties of bioplastic are important for...

The effect of injection timing on energy and exergy analysis of a diesel engine with biodiesel fuel

Introduction Nowadays, due to higher environmental pollution and decreasing fossil fuels many countries make decisions to use renewable fuels and restrict using of fossil fuels. Renewable fuels generally produce from bio...

Download PDF file
  • EP ID EP717898
  • DOI -
  • Views 41
  • Downloads 0

How To Cite

S. Mollazehi, H. Sadrnia, M. R. Bayati, (2018). Prediction of Temperature Distribution within a Piece of Date Palm Trunk during the Microwave Heating Treatment to Control Rhynchophorus Ferrugineus. Journal of Agricultural Machinery, 8(2), -. https://europub.co.uk/articles/-A-717898