Surface functionalization of poly(L-lactide-co-glycolide) membranes with amphiphilic poly(2-oxazoline) for guided tissue regeneration and treatment of bone tissue defects
Journal Title: Engineering of Biomaterials / Inżynieria Biomateriałów - Year 2018, Vol 21, Issue 147
Abstract
The main challenge of this research was to functionalize the surface of poly(L-lactide-co-glycolide) (PLGA) membranes with amphiphilic poly(2-oxazoline) (POx) in order to change PLGA chemical state and properties. Poly(2-oxazolines) are very powerful polymers, which thanks to active pendant groups can be easily functionalized with biologically active molecules or peptides. The membranes were prepared by dissolving PLGA, POx, and poly(ethylene glycol) (PEG, 1000 Da) in methylene chloride (DCM), followed by PEG leaching. POx molecules were preferentially adsorbed at the interface PLGA-POx-PEG thanks to affinity to both hydrophilic (PEG) and hydrophobic (PLGA) chains. The properties of the membranes were characterized with Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and wettability tests. Cytocompatibility of the materials in contact with osteoblast-like MG-63 cells was studied by evaluation of cell viability (Alamar- Blue test), live/dead and phalloidin/DAPI staining. The results show that the presence of POx influenced topography of the PLGA membranes, but did not have an impact on their wettability. All membranes were found cytocompatible with model osteoblasts. Presence of POx resulted in better cell adhesion as shown by microscopic studies after fluorescence staining for nuclei and cytoskeleton actin filaments. In summary, one-step phase separation process between PLGA, PEG, and POx, dissolved in DCM followed by drying and PEG leaching resulted in cytocompatible PLGA membranes with immobilised POx, which might be considered for guided tissue regeneration technique in periodontology and in bone tissue engineering.
Authors and Affiliations
A. M. Tryba, M. Krok-Borkowicz, C. Paluszkiewicz, E. Pamuła
Keywords
Related Articles
- EP ID EP553975
- DOI -
- Views 54
- Downloads 0
Material and corrosion studies of conventional Co-Cr-Mo-W alloys for frame construction casts in dental prosthetics
The basic characteristics of skeletal prosthetic materials used in dentistry are: biotolerance with tissues and body fluids, as well as high pitting and crevice corrosion resistance. Also important are such characteristi...
Improvement of short Ca-P whiskers/polylactide composites by surface modification with lauric acid
Polymer-ceramic composites are widely used in regenerative medicine, especially in orthopedics, as there are many methods of modifying their properties depending on the intended use. One of them is filling the polymer ma...
Kofeina jako czynnik modyfikujący hydrożele akrylowe
Hydrożele są materiałami zbudowanymi z łańcuchów polimerowych, które tworzą trójwymiarową i usieciowaną strukturę. Mają one bardzo dużą zdolność do pochłaniania wody, stąd też bardzo często są nazywane superabsorbentami....
Wpływ dodatku kwasów karboksylowych na czas wiązania i wytrzymałość na ściskanie cementów szkło-jonomerowych
Cementy szkło-jonomerowe powstają w czasie utwardzania kompozycji złożonych z dwóch składników: szklanego proszku i płynu wiążącego będącego wodnym roztworem polikwasów alkenowych. Wiązanie cementu polega na reakcji kwas...
Charakterystyka mechaniczna wielofunkcyjnej resorbowalnej płytki kompozytowej do zespoleń kostnych
W artykule przedstawiono badania mechaniczne prototypowego wszczepu do zespoleń kostnych w postaci resorbowalnej wielofunkcyjnej czterootworowej płytki w kształcie litery I. Testy dotyczyły gotowych implantów w symulowan...