ELECTROMECHANICAL PROCESSES IN A LINEAR PULSE-INDUCTION ELECTROMECHANICAL CONVERTER WITH A MOVABLE INDUCTOR AND TWO ARMATURES
Journal Title: Електротехніка і Електромеханіка - Year 2018, Vol 0, Issue 2
Abstract
Purpose. The purpose of the paper is to determine the influence of the height of the mobile and stationary disk electrically conductive armatures covering the movable inductor on the electromechanical processes of linear pulsed-induction electromechanical converter (LPIEC). Methodology. With the help of the developed mathematical model that describes electromechanical and thermal processes of LPIEC, the influence of the heights of the armatures on electromechanical processes, the values of the electrodynamic forces acting on the inductor and armature, and the moving speed of the movable armature (MA) is established. Results. It is shown that if the height of the stationary armature (SA) is twice the height of the MA, then the inductor at the initial instant of time is acted upon by electrodynamics forces pressing it to the SA, and the displacement of the inductor begins with a delay of 0.35 ms. If the height of the MA is twice the height of the SA, then the electrodynamics forces act on the inductor at the initial instant of time, repelling it from the SA, and its movement begins with a delay of 0.1 ms. If the heights of the SA and the MA are equal, then until the time 0.15 ms on the inductor, the electrodynamics forces practically do not act and the inductor moving relative to the SA begins with a delay of 0.25 ms. Originality. The effect of the geometric parameters of the SA and MA on the velocity of the inductor moving relative to the SA, MA relative to the inductor and the MA relative to the SA is established. It has been established that the highest velocity of the MA relative to the SA develops the lowest MA, and the height of the SA does not affect it practically. However, with the increase in the height of the MA, the effect of SA begins to affect. In this case, it is expedient to select the height of the SA to be 0.4-0.42 of the height of the inductor. Practical value. It is shown that as the weight of the actuating element increases, the currents in the active elements of the LPIEC increase, the induction velocities of the inductor relative to the SA and the MA decrease relative to the inductor. At the same time, the maximum the electrodynamic forces values acting on the inductor decrease, and the armatures increase. Moreover, the maximum the electrodynamic forces acting on the MA are less than similar forces acting on the SA.
Authors and Affiliations
V. F. Bolyukh, A. I. Kocherga, I. S. Schukin
Keywords
Related Articles
- EP ID EP486172
- DOI 10.20998/2074-272X.2018.2.02
- Views 77
- Downloads 0
PROFESSOR P.P. KOPNIAIEV – SCIENTIST, PUBLIC PERSON, ESTABLISHER OF HIGHER ELECTRICAL ENGINEERING EDUCATION (to the 150th anniversary of his birth)
Purpose. To carry out complete historical and scientific analysis of Professor P.P. Kopniaiev's activities and establish his role and place of achievements in the formation of the basic concepts and directions of the the...
NETWORK-CENTRIC TECHNOLOGIES FOR CONTROL OF THREE-PHASE NETWORK OPERATION MODES
Purpose. The development of the control system for three-phase network is based on intelligent technologies of network-centric control of heterogeneous objects. The introduction of unmanned aerial vehicles for monitoring...
AN ANTHOLOGY OF THE DISTINGUISHED ACHIEVEMENTS IN SCIENCE AND TECHNIQUE. PART 44: TRADITIONAL POWER ENGINEERING. NUCLEAR POWER STATIONS: RETROSPECTIVE VIEW, STATE AND PROSPECTS OF THEIR DEVELOPMENT
Purpose. Preparation of brief scientific and technical review about a retrospective view, modern state, achievements, problems, tendencies and prospects of development of world nuclear energy. Methodology. Known scientif...
ESTIMATING THE LIMIT POSSIBILITIES OF THE STEP CHARGING SYSTEM FOR CAPACITIVE ENERGY STORAGE
The aim of the article is to estimate the limit possibilities of step-by-step charging the capacitive energy storage which are caused by the achievement of a balance among the processes of the receiving and losing of ele...
CALCULATION METHOD OF ELECTRIC POWER LINES MAGNETIC FIELD STRENGTH BASED ON CYLINDRICAL SPATIAL HARMONICS
Purpose. Simplification of accounting ratio to determine the magnetic field strength of electric power lines, and assessment of their environmental safety. Methodology. Description of the transmission lines of the magnet...