Micromechanical Behavior of Potato Tissue by Scanning Electron Microscopy: Effect of Storage Time, Impact Energy and Curvature Radius of Impact Location
Journal Title: Journal of Agricultural Machinery - Year 2018, Vol 8, Issue 2
Abstract
Introduction The mechanical impacts occur mainly during harvesting and post-harvesting operations, lead to the breaking of cell membranes in cellular structure that dependS on impact intensity. Furthermore, turgor pressure of potato tissue is influenced by the micromechanical and the physiological changes in the storage duration. Micromechanical changes of potato tissue due to the mechanical impact need to be monitored by microscopic images during storage. Scanning electron microscopy (SEM) is a high-resolution technique used to investigate the micromechanical behavior of potato tissue. Materials and Methods Potato samples (âSanteâ cultivar), were stored at 5 ± 0.5°C and 85% relative humidity for 16 weeks. By 2-week intervals, potatoes were removed from the storage and then the impact test was done. Experimental factors were impacted energy at three levels of control (no impact was done), impact energy 1 (0.031 ± 0.002 J) and impact energy 2 (0.320± 0.020 J) and the radius of curvature at two levels of (35 and 45 mm). Water content was measured by drying thin slab samples in an oven at 70°C to a constant weight. The cell turgor pressure of potato tissue at 2-week intervals was estimated from the linear regression between turgor values of each mannitol solution (0â0.6 M) and relative volume change. The microstructural changes of impact location on the potato tubers were analyzed by SEM images at 2-week intervals during storage period. The surface and depth sections cutting from the impact location were immediately immersed in 2.5% glutaraldehyde in 0.1 M sodium phosphate buffer (2 h) at 4± 0.5°C. The specimens were then rinsed 3 à 10 min in 0.1 M sodium phosphate buffer (pH 7.2), and dehydrated through an ethanol series, 25, 50, 70, 90 and 100% dry, 15 min each step, 2 à 100%. In this study the HMDS as a high-quality chemical drying was investigated. The sample preparation for SEM observation then followed by chemical drying via HMDS, under a laboratory hood overnight. Analysis of variance test based on completely randomized design (CRD) was considered for all of the data using SPSS 23. Results and Discussion Superior preservation of potato microstructure was obtained by hexamethyldisilazane (HMDS) drying during sample preparation for SEM observation. The MIP software was used for quantitative analysis of SEM images and the microstructural features of potato tissue at the impact location were determined. So that each cell outline was manually separated by drawing the lines along the visible contours of cell walls. Measurement of the impact damage dimensions was done by MIP software for the surface section (major and minor width, w1 and w2) and the depth section (depth, d and major width, w1). The results indicated the significant differences between water content, cell turgor pressure, cell area and cell perimeter over 16 weeks storage. Generally, by increasing impact intensity the water content, cell turgor pressure, cell area and cell perimeter significantly decreased. Also interaction effect of storage time, impact level and radius of curvature for impact damage of potato tissue was significant. Conclusion The cell turgor pressure at the impact location on the potato tubers had the similar trend with the water content. SEM investigation showed that potato parenchyma, which was high preserved by HMDS drying, had consisted of the pentagon and hexagonal thin-wall cells with the average cell area of 23.14 à 103 ± 0.178 μm2, the average cell perimeter of 564.98 ± 2.008 μm at week 0. The higher impact damage was at week 16 of storage, impact level 2 and the radius of curvature of 35 mm compared to the other treatment.
Authors and Affiliations
S. Youneji,E. Ahmadi,A. Alavi Nia,
Keywords
Related Articles
- EP ID EP717900
- DOI -
- Views 40
- Downloads 0
Design, Development and Evaluation of a Pneumatic Seeder for Automatic Planting of Seeds in Cellular Trays
For planting fine seeds in cellular trays, an automatic pneumatic seeder was designed, constructed and evaluated. CATIA software was used to design and analysis the system parts of the seeder. Different parts of the seed...
Modeling of Yield Estimation for The Main Crops in Iran Based on Mechanization Index (hp ha-1)
Agricultural mechanization is a method for transiting from traditional agriculture towards industrial and sustainable one. Due to the limitation of natural resources and increasing population we need to have economical p...
Computer Vision Utilization for Detection of Green House Tomato under Natural Illumination
Agricultural sector experiences the application of automated systems since two decades ago. These systems are applied to harvest fruits in agriculture. Computer vision is one of the technologies that are most widely used...
Fabrication and evaluation of variable rate fertilizer system
Introduction: In conventional farming, the soil and crop are considered uniform in different locations of the farm and the fertilizers are applied according to the average of soil needs with an additional percentage for...
Desien, ConstruThe design, fabrication and evaluation of egg weighing device using capacitive sensor and neural networksction and Evaluation of Egg Weighing Device Using Capacitive Sensor and Neural Networks
Introduction: Grading agricultural products always has a particular important position for submission to domestic and overseas markets. The grading causes more profitable product ranges and customer satisfaction. Grading...