Shear Bond Strength of Resin Bonded to Bleached Enamel Using Different Modified 35% Hydrogen Peroxides
Journal Title: Journal of Dental Biomaterials - Year 2015, Vol 2, Issue 4
Abstract
Statement of Problem: Bleaching systems with different concentrations and applications are widely used to improve the visual appearance of the teeth, but one of the complications of these materials is reduction of bond strength for immediately bonding to the bleached enamel. Objectives: The aim of this study was to evaluate the influence of using different modified hydrogen peroxide bleaching agents on the shear bond strength of composite resin bonded to the bleached enamel. Materials and Methods: Forty-eight sound extracted premolar teeth were collected, sectioned 1 mm below the CEJ to detach the root. The proximal surfaces of the teeth were flattened using diamond disks and silicon carbide papers to achieve flat homogeneous enamel surfaces without exposure to the dentin. The teeth were randomly divided into four groups as follows (n = 12): group 1: bleaching with 35% hydrogen peroxide gel; group 2: bleaching with 35% hydrogen peroxide gel contained (casein phosphopeptide-amorphous calcium phosphate (CPP-ACP); group 3: bleaching with 35% hydrogen peroxide gel combined with fluoride; and group 4: bleaching with 35% hydrogen peroxide applying one week before resin restoration placement. Composite resin, Clearfil AP-X (Kuraray, Tokyo, Japan), was bonded on each tooth in the mould (4 mm diameter × 3 mm height) using Clearfil SE Bond (Kuraray, Tokyo, Japan). After 24 hours of storage and 1000 cycles of thermocycling, the shear bond strength of the specimens at a cross-head speed of 0.5 mm/min was measured in MPa. Data were analyzed using ANOVA and Tukey’s post-hoc test. Results: The minimum and maximum mean shear bond strength values were observed in groups 2 (15.82 ± 4.41) and 4 (21.00 ± 3.90), respectively. Multiple comparisons of groups revealed no significant differences among the groups except between group 4 and all the other groups. The most common type of failure was adhesive. Conclusions: Using modified bleaching agents decreased the bond strength of the composite resin to the enamel when it was used immediately after bleaching.
Authors and Affiliations
H Moosavi, M Shaykhvasy
Keywords
Related Articles
- EP ID EP248927
- DOI -
- Views 51
- Downloads 0
Comparison of Microtensile Bond Strength of Silorane-Based Composite with the Conventional Methacrylate Composite to the Dentin of Primary Teeth
Statement of Problem: The bond strength between restorative material and tooth structure is so important for conduction of durable restoration. Considering the recent attention to low shrinkage composite resins, evaluati...
Effect of Smear Layer Removal on Bond Strength of Two Different Resin-Based Sealers; an In Vitro Study
Statement of Problem: During root canal preparation, organic pulpal ma-terials, bacteria and blood cells in combination with inorganic dentinal debris accumulate on the canal wall, producing an amorphous irregular smear...
Effect of Different Irrigation Solutions on the Colour Stability of Three Calcium Silicate-Based Materials
Statement of Problem: Previous studies have shown discoloration of mineral trioxide aggregate (MTA) in contact with root canal irrigation solutions. However, there are limited data on colour stability of other calcium si...
The Effect of Two Types of Denture Adhesive on the Satisfaction Parameters of Complete Denture Wearers
Statement of Problem: Patient satisfaction is highly influenced by the retention of the denture. In some instances using denture adhesives may help the patient to achieve this goal. Objectives: The purpose of this study...
The Effect of Pre-heating Silorane-based Composite Resin on Marginal Gap Formation of Class V Restorations
Statement of problem: Many efforts have been made to solve the problem of composite resin adaptation and reduce microleakage. Objective: The aim of the present study was to evaluate the effect of preheating of silorane-b...