Two Component Injection Moulding of Bi-material of Stai
Journal Title: Jurnal Kejuruteraan - Year 2017, Vol 29, Issue 1
Abstract
The two component injection molding (2C-PIM) is a promising technique for production of small, complex and high density, metal-ceramic parts in large scales. This method is a viable option for integrating incompatible functions or properties of the materials in a singular part or component. Thus, the production of near net shaped components via 2C-PIM is imperative due to cost effectiveness resulting from high unit volumes. In this study, the feasibility of joining stainless steel (17-4PH) and 3mol% yttria stabilized zirconia (3YSZ) materials in their green states was investigated. Two feedstock of SS17-4PH and 3YSZ powder materials was prepared based on optimum solid loading of 3vol% lower than value of the critical loading. The critical solid loading for the SS17-4PH and 3YSZ powder materials were 71vol% and 53vol% respectively, based on the oil absorption technique ASTM: D-281-12. The binder system utilized comprises of 60wt.% palm stearin (PS) and 40wt.% low density polyethylene (LDPE). The two materials were injected sequentially using the screw type injection molding machine (BOY 22A) to form a bi-material component. The green properties were investigated. The morphology of the individual green parts and composites depicted that the powders were optimally dispersed in the binder matrix indicating good mixture and compaction of the green components. The flexural strength of the single components of the bi-material was above 5 MPa. The strength of the bonding zone which was 1.4 MPa indicates an evidence of bonding.
Authors and Affiliations
Ukwueze Bonaventure Emeka, Abu Bakar Sulong, Norhamidi Muhamad, Zainuddin Sajuri
Keywords
Related Articles
- EP ID EP417481
- DOI 10.17576/jkukm-2017-29(1)-07
- Views 105
- Downloads 0
Measurement of Gas Holdup and Mass Transfer in a Bubble Column by Using Electrical Resistance Tomography (ERT)
Gas dispersion performance and gas hold-up in a bubble column was investigated by using electrical resistance tomography (ERT). Experiments were carried out to visualize flow pattern and gas hold-up at different gas velo...
Preliminary Study of Alkaline Direct Ethanol Fuel Cell by Using Crosslinked Quaternized Poly (Vinyl Alcohol)/Graphene Oxide Membrane
A crosslinked of Quaternized Poly (vinyl alcohol)/Graphene oxide (QPVA/GO) composite membrane was prepared via quaternization and solution casting method. With the main objective is to performed lower ethanol permeabilit...
Hubungan di antara Pelaksanaan 5S dan Prestasi Hijau Syarikat Pembuatan PKS di Malaysia: Satu Model Konsep (Relationship between 5S Implementation and Green Performance of Malaysian Manufacturing SMEs: A Conceptual Model)
Because of the global sustainability agenda, environmental factors are increasingly becoming a priority in the implementation of management practices and competitiveness strategies. Management system such as ISO 9001 and...
Kesan Penjana Fotovolta Tersambung-Grid terhadap Kestabilan Voltan Dinamik dalam Sistem Kuasa (Effect of Grid-Connected Photovoltaic Generator on Dynamic Voltage Stability in Power System)
Penyepaduan penjana fotovolta (FV) tersambung-grid ke dalam sistem kuasa memberi kesan teknikal kerana reka bentuk rangkaian asalnya tidak mengambil kira penyepaduan penjanaan teragih. Pertumbuhan pesat pemasangan dan pe...
Pembentukan Mikrostruktur Berbentuk Sfera dalam Keadaan Separa Pepejal Aloi Aluminium Al-4.8Si-2.8Cu-0.5Mg (Formation of Spheroidal Microstructure in Semi-solid State of Al-4.8Si-2.8Cu-0.5Mg Aluminium Alloy)
Hasil penyelidikan mengenai pembentukan mikrostruktur berbentuk sfera dalam keadaan separa pepejal aloi aluminium Al-4.8Si-2.8Cu-0.5Mg dibentangkan dalam penulisan ini. Bahan awal aloi aluminium tersebut dihasilkan melal...