Investigation of the porous GaP layers' chemical composition and the quality of the tests carried out
Journal Title: Journal of Achievements in Materials and Manufacturing Engineering - Year 2018, Vol 2, Issue 86
Abstract
Purpose: The purpose of this study is to establish the quality of tests for determining the chemical composition of the porous surface obtained by the method of electrochemical etching, based on the indicators of convergence and reproducibility of the results. Design/methodology/approach: The method of electrochemical etching was used to obtain layers of porous gallium phosphide, which can be used as buffer layers for nitrides formation on their basis. Por-GaP was formed in a solution of hydrofluoric acid at a current density of j =100 mA/cm2, etching was carried out for 20 minutes. The resulting structures sulfide passivation was carried out, thus avoiding the formation of an oxide film on the samples surfaces. For this purpose, porous gallium phosphide samples were kept in a sulfide solution for 10 minutes and dried in a stream of nitrogen. The chemical composition of the porous GaP surface layers has been investigated. To do this, the method of electronprobe INCA Energy microanalysis was used. The research was carried out on the entire surface of the sample in order to calculate the total spectrum of the elemental composition of the sample under study. Findings: It was established that during anodizing, the stoichiometry of the crystals investigated did not shift significantly towards the excess of gallium atoms. Oxygen is present at an insignificant concentration of 0.3%. This indicates the effectiveness of conducting the sulfide passivation of the sample surface following the electrochemical treatment. The presence of fluorine atoms that appeared on the surface as a result of the reaction with the electrolyte during etching, is observed in extremely low concentration. Experimental studies have shown that the sample chosen can be used as a standard enterprise sample when analyzing the chemical composition of the surface of porous gallium phosphide due to its convergence, reproducibility, homogeneity. In addition, the given method for determining the standard sample can be applied to other porous semiconductors. Conducting such studies is an important technological task that will allow us to create a series of standard samples of porous semiconductors of A3B5 group. Research limitations/implications: The research was carried out for porous gallium phosphide samples synthesized in the solution of hydrofluoric acid, though, carrying out of similar experiments for por-GaP obtained in other conditions, is necessary. Practical implications: The studies of the reproducibility and convergence of the experiment have an important practical significance, since it is the reproducibility of the experiment results that is the main problem to modern material science, all the more to nanoengineering. Therefore, the technique proposed, will allow the synthesis of por-GaP layers with adjustable properties, will facilitate their widespread implementation in the real sectors of industry. The obtained porous layers can be used as standard samples. Originality/value: The main problem in the nanostructures synthesis is the adjustability of properties. The technique presented allows to form stable layers of the porous gallium phosphide with the surface chemical composition known in advance. In addition, carrying out the sulfide passivation allows to stabilize por-GaP properties, which is an important process task. For the first time, a study of the presented technique as to convergence, reproducibility and homogeneity, was conducted.<br/><br/>
Authors and Affiliations
S. Vambol, V. Vambol, Y. Suchikova, I. Bogdanov, O. Kondratenko
Keywords
Related Articles
- EP ID EP346015
- DOI 10.5604/01.3001.0011.8236
- Views 88
- Downloads 0
The comparison of the sintering methods for diamond cutting tools
Purpose: Aim of this study is to compare mechanical, physical, microstructural propertiesof diamond cutting tools (DCTs) made of Co-Ni-Cu-Sn matrix, produced by Spark PlasmaSintering (SPS) and Conventional Sintering (CS)...
Effect of combinative cooled addition of strontium and aluminium on mechanical properties AlSi12 alloy
Purpose: The study was to determine the mechanical properties of hypo-eutectic silumin AlSi12 modified with Sr or Al-Sr alloy slow or fast cooled and in the form of a strip or powder. Design/methodology/approach: The exp...
Estimation of the chemical specific surface area of catalytic nanoparticles by TEM images analysis
Purpose: The purpose of this article is the development of quantitative methods for assessing the quality of nanocomposite materials used in fuel cells. Design/methodology/approach: latinum is the most commonly used cata...
Modelling of superplastic deformation for metallic alloys using a cavity based approach
Purpose: In this study, modeling of superplastic deformation characteristic for metallic alloys was investigated using GTN failure criteria in viscoplastic framework. Design/methodology/approach: The proposed model studi...
Electromagnetic analysis of magnetorheological brakes
Purpose: In this proposed work, make a electromagnetic analysis of magnetorheologicalbrake for creating the automobile structure under the drive by wire concept.Design/methodology/approach: The proposed brake system cons...