Manufacturing process and optical properties of zinc oxide thin films as photoanode in DSSC
Journal Title: Journal of Achievements in Materials and Manufacturing Engineering - Year 2018, Vol 1, Issue 86
Abstract
Purpose: It has been recently observed, that zinc oxide thin films are gaining much popularity, particularly in applications such as toxic gas sensors, photocatalytic materials and photovoltaic cells. Due to much better physical properties of ZnO compared to the ones of titanium dioxide (TiO2), which is currently the most used material in dye sensitized solar cells, efforts are being made to fabricate DSSCs with thin films and/or nanostructures, including nanowires, nanofibres and nanoparticles of zinc oxide. Design/methodology/approach: In this paper, zinc oxide thin films were prepared using sol-gel and spin coating methods from Zn(COO)2 x 2H2O dissolved in ethanol and acetic acid with ZnO monocrystalline nanoparticles of 0 and 10% (wt.) relative to the final concentration of produced solutions. The effect of calcination process on ZnO thin films at 600°C were examined using atomic force microscope to investigate the morphology of semiconductor coatings, infrared spectroscopy to prove the chemical structure of material. Besides, optical properties were analysed on the basis of absorbance in the function of wavelength spectra and the values of energy band gaps were studied. Findings: The topography analysis of ZnO thin films showed an increase in roughness with the increase of zinc oxide nanoparticles in the thin films material. In addition, the analysis of the optical properties of ZnO thin films showed a decrease in absorption level in the range of near-ultraviolet wavelength for the obtained layers after annealing. Research limitations/implications: It was found that ZnO thin films produced by spin coating and calcination method are a proper material for photoanode in dye-sensitized solar cells, as zinc oxide layers provide better conductivity across the photovoltaic cell. Practical implications: The results provide the possibility of production DSSCs with zinc oxide thin films as photoanode. Originality/value: The dye-sensitized solar cells based on zinc oxide photoanodes could be alternative semiconductor material to titanium dioxide, which is used in nowadays solar cells. It was estimated that ZnO, especially zinc oxide nanostructures have much better physical properties, than TiO2 structures. What is more, zinc oxide thin layers are characterized by the lower energy losses resulting from the physical properties of such nanostructures, which results in more efficient solar energy into electricity conversion.
Authors and Affiliations
Wiktor Matysiak, Tomasz Tański, Marta Zaborowska
Keywords
Related Articles
- EP ID EP270272
- DOI 10.5604/01.3001.0011.6016
- Views 71
- Downloads 0
Effect of heat treatment on the tensile properties of cam shaft made of ductile cast iron
Purpose: The aim of this study is to investigate effects of austempering heat treatment onthe tensile properties of GGG60 ductile cast iron for cam shaft production. For this purpose,cam shafts have been produced by sand...
Virtual laboratory methodology in scientific researches and education
Purpose: This article is presenting the Material Science Virtual Laboratory. Developed laboratory is an open scientific, investigative, simulating and didactic medium helpful in the realisation of the scientific and dida...
Investigation of mechanical properties of MIG-brazed joints of DP600 steel plates using different working angle
Purpose: In this study, DP 600 (Dual Phase) steel plates having 1 mm thickness were joined by copper-based (CuAl8) wire in gas metal arc brazing technique. Specimens were prepared in joining forms as overlap joint. Desig...
Investigation of mechanical properties of MIG-brazed joints of DP600 steel plates using different working angle
Purpose: In this study, DP 600 (Dual Phase) steel plates having 1 mm thickness were joined by copper-based (CuAl8) wire in gas metal arc brazing technique. Specimens were prepared in joining forms as overlap joint. Desig...
Surface morphology of wheels in rail vehicles in urban transport
Purpose: The general purpose of presented research was evaluation of surface morphology of chosen tram wheels: LUCCHINI (of Siemens Combino tram), PST (of Moderus Beta tram), and GT no 1 (of Duewag tram) operating in Poz...